Cut-Weld-Drive Forums

Cut-Weld-Drive Forums (http://volksrods.com/forum/index.php)
-   The Tech Bin (http://volksrods.com/forum/forumdisplay.php?f=17)
-   -   Today I (http://volksrods.com/forum/showthread.php?t=35936)

Guss June 23rd, 2012 07:38 PM

Today I
 
We are still working on the Scout. Daddy had a big story about it, but he told me I can do this part. So this is my first how to do it post ever. I made all new brake lines from a big roll not little pieces that already have the ends on it. The first ones daddy did to show me how. He made the two that go from the tires to the middle and I made the one that goes from there all the way to the front.

First you have to cut the line and file the end so it was smooth and get the inside smooth too. That way it will fold over right. Then you have to put the nut on the line. Don't forget. I forgot the first time and had to do it over. Then you put it in the holder tool. You have to use the black piece to measure to make sure it isn't to short or to long.

http://img.photobucket.com/albums/v6...E/IMAG0124.jpg


Then you turn the black piece over and stick the peg inside the line and make sure that it is even. If it is lower on one side it will not do good.

http://img.photobucket.com/albums/v6...E/IMAG0125.jpg


Then when it is even, you tighten the clamp down until it stops.

http://img.photobucket.com/albums/v6...E/IMAG0126.jpg


This is how it should look. The hole in the tube is in the middle not off to the side.

http://img.photobucket.com/albums/v6...E/IMAG0127.jpg


Then you put the clamp back on, but this time don't use the black part. You just use the clamp and tighten it until it stops.

http://img.photobucket.com/albums/v6...E/IMAG0128.jpg


When you take the clamp off it should look like this.

http://img.photobucket.com/albums/v6...E/IMAG0129.jpg


Then you take the holder tool off and use a file to smooth the places where the holder made cuts in the line. If you don't the nut doesn't turn good and it is hard to tighten when you put it on the truck.

http://img.photobucket.com/albums/v6...E/IMAG0130.jpg

http://img.photobucket.com/albums/v6...E/IMAG0131.jpg


Then you bend it. But that is part of daddy's story so he gets to tell you about that.

bigguy June 23rd, 2012 08:10 PM

Re: Today I
 
Nice write up guss. You look more and more like your dad. Even the hairdo is something he would do.

Scott76 June 23rd, 2012 08:16 PM

Re: Today I
 
That is great to see you getting your hands in there and learning a true trade that WILL help you out in life. Keep up the hard work and always listen to the advice your dad gives you.

Great work on the tire fix too.

Ace of Shades June 23rd, 2012 08:26 PM

Re: Today I
 
Dig the hair. It takes a while to get down just right, but a double flare is something that you will use what seems like every time you work on a car.

Great bonding time, amazing to see knowledge passed down, and just cool beens to kids take an interest in learning :thumbsup:



And it gives me hope to know that there are people and kids out there learning to do things for themselves. and I'm sure Ray-Dean isn't a participation trophy guy, So everything is earned

and if you don't like it, don't post about it


Ray-Dean June 23rd, 2012 08:26 PM

Re: Today I
 
Quote:

Originally Posted by bigguy (Post 544589)
.... Even the hairdo is something he would do.



What the hell Pooky? Them there is his devil horns. I tell ya wut, little kids think twice about steeling home when the kid behind the plate has horns...


http://img.photobucket.com/albums/v6...96115739_n.jpg


To date, a few have tried, and none have made it. This was about a month ago when we got to go out on the field with the Drillers.

bigguy June 23rd, 2012 08:36 PM

Re: Today I
 
It just looks like something you would do. lol. I remember the mohawk. lol

StickerDick June 24th, 2012 07:02 AM

Re: Today I
 
Good Job!

SCOTTRODS June 24th, 2012 07:28 AM

Re: Today I
 
Hell..... That's a better write up than a lot of "big people" have done.... Nice work.

I'm watchin' this kid..... He's a quick learner. If he's creative, by the time he's 20, we'll be lookin' at a High-end Custom builder.


All times are GMT -8. The time now is 01:45 AM.

Powered by vBulletin
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
ALL text, images, graphics and content herein are Copyright 2002 - 2013 Three Pugs Design - Cut Weld Drive Forums